Aiwa VX-T1470PH Uživatelský manuál stáhnout pdf

AIWA VX-T1420

R1083 S6-150-12R-7J0 RES.FUSE 2.7-1W

IC351 S0-1SP-526-500 IC, AN5265

IC1002 S0-7S0-247-V10 IC, BA6247-V1

IC1004 S0-QK9-780-500 IC, NJMT805FA

IC5001 S0-3D7-728-600 IC, LA7286

Q5003 89-313-172-010 TR, 2SC1317

T5001 S3-362-600-8R0 COIL, BIAS OSC 3626008

TU6001 S1-44T-070-190 TUNER, UHF/UE33-B5

R423 87-029-007-010 RES, FUSE 22 - 1/4W

R445 87-022-304-010 RES, M/O 1.5K - 3W

R446 87-022-304-010 RES, M/O 1.5K - 3W

R447 S6-158-268-0J0 RES, FUSE 68 - 1/2W

R448 S6-358-210-2J0 RES, FUSE 1K - 1/2W

R449 S5-K2C-E8R-2K0 RES, CEM 8.2 - 7W

S5-K2C-E8R-2K0 RES, CEM 8.2 - 7W

R450 87-029-160-010 RES, FUSE 2.2 - 1W

R451 87-029-164-010 RES, FUSE 4.7 - 1W

R452 S6-358-11R-8J0 RES, FUSE 1.8 - 1W

R501 S5-Y2C-E2R-2J0 RES, CEM 2.2 - 7W

R504 S3-X28-947-3J0 RES, M/O 47k - 3W

R505 87-025-072-010 RES, M/O 100 - 1W

R506 87-029-389-010 RES, FUSE 1K - 1/4W

R508 S3-K28-BR8-2J0 RES, M/O 0.82 - 3W

R511 S6-3480-A12-0J0 RES, FUSE 12 - 2W

R512 87-022-384-010 RES, M/O 8.2K - 2W

R513 53-U28-A15-0J0 RES, M/O 15 - 2W

C515 87-010-964-010 CAP, E 10 - 160V

C536 SA-303-091-3M0 CAP, CER 1000PF 400V

C542 SA-303-09H-3M0 CAP, CER 2200PF 400V

C546 SA-303-09H-2K0 CAP, CER 220PF-4KV

D501 S2-BTR-M11-C00 DIODE, RM11C

D502 S2-BTR-M11-C00 DIODE, RM11C

D503 S2-BTR-M11-C00 DIODE, RM11C

D504 S2-BTR-M11-C00 DIODE, RM11C

D509 S2-8T1-0EL-S60 DIODE, 10ELS2TA1

D510 S2-811-5DF-600 DIODE, 15DF6-FC

D511 S2-8T1-0EL-520 DIODE, 10ELS2TA1

D512 S2-811-000-400 DIODE, 21DQ04FE5R

D513 S2-80F-5KF-200 DIODE, F5KF20

IC402 87-002-524-010 IC, LA7837

IC403 S0-X39-8M0-900 IC, UPC78M09H

IC501 S2-359-006-000 IC, STK730-060

IC502 S0-3A9-780-5V0 IC, L7805V

IC503 S0-1K9-780-900 IC, AN7809F

Q402 SD-UG0-155-400 TR, 2SD1554

Q503 SC-300-416-000 TR, 2SC4160

Q504 SD-3T0-073-400 TR, 2SD734 (E, F, G) - AA

L501 S2-940-000-620 COIL, FILTER RB-20871

L502 S2-920-000-250 COIL, FILTER RB-20871

FB401 S4-321-300-9F0 TRANS, FLYBACK 3213009

T501 S4-813-501-5W0 TRANS, SW 8135015W

F501 S8-08T-2R5-020 FUSE, 4A - 250V T

RY501 S5-60Q-101-120 RELAY, OST-S-109DM

ICP501 S8-32H-1R6-010 IC, lCP - 1.6A

ICP502 S8-32H-020-010 IC, ICP - 2.0A

ICP503 S8-32H-050-010 IC, ICP - 5A

R802 S3-X18-A10-3J0 RES, M/O 10K - 2W

R805 S3-X18-A10-3J0 RES, M/O 10K - 2W

R810 S3-X18-A10-3J0 RES, M/O 10K - 2W

R916 S6-158-427-0J0 RES, FUSE 27 - 1/4W

J801 S6-661-200-110 SOCKET CRT, CVT3325-0603

L503 S2-8H1-400-180 COIL, DEGAUSS 8H140018

CD501 S2-066-358-020 CORD AC 1206635802

V801 S9-8Q1-404-250 CRT, 370KRB22-T

L1301 S2-BH0-000-060 ELECTRO MAGNET JTM1012-01

M101 SS-96P-580-080 MOTOR LOAD MXN-13FB

M2001 SS-10S-980-240 CAPSTAN UNIT F2QTBO2

M2003 SS-895-110-070 MOTOR, E20EL93

UN4001 S4-A05-8A5-000 CYLINDER ASS’Y A4A058A500

Disassembly Instuctions

2. REMOVAL OF DECK PARTS

2-1: ACTUATOR SUB BRAKE / IDLER ASS’Y

(Refer to Fig. 2-1)

1. Remove the polyslider washer (1)

2. Remove the Idler Ass’y.

3. Remove the TS Brake Spring.

4. Remove the Actuator Sub Brake

Fig. 2-1

2-2: TENSION BAND (Refer to Fig. 2-2)

1. Remove the Actuator Sub Brake.

2. Remove the SS Brake Spring, then remove

the SS Brake Arm.

3. Remove the screw (1).

4. Move the SB Brake Arm for movable range.

Remove the Tension Band Assy from the

Tension Arm Ass’y.

NOTES

1. Install the Tension Band Ass’y without twisting

it.

2. Adjust the placement of the Tension Post.

(Refer to item 1-2 of MECHANICAL ADJUST-

MENTS)

3. Adjust and confirm the back tension during

playback. (Refer to item 1-3 of MECHANICAL

ADJUSTMENTS)

Fig. 2-2

2-3: REEL DISK (Refer to Fig. 2-3)

(Reel Disk S Assy)

1. Remove the Actuator Sub Brake.

2. Remove the washer (4), then remove the SB

Brake Arm.

3. Remove the SS Brake Spring, then remove

the SS Brake Arm.

4. Remove the Tension Band assy from the

Tension Arm Ass’y.

5. Remove the polyslider washer (1).

6. Pull the Reel Disk S Ass’y upward and

replace it.

NOTE

When you replace the SB Brake Arm, use the

new washer (4) of the SB Brake Arm.

(Reel Disk T Ass’y)

1. Remove the TS Brake Spring.

2. Remove the Actuator Sub Brake.

3. Move the TS Brake Assy in the direction of

arrow.

4. Remove the Brake TB 2 Ass’y.

5. Remove the polyslider washer (2).

6. Pull the Reel Disk T Ass’y upward and replace

it.

NOTES

1. The height adjustment washers (3) are

sometimes attached to the back of the Reel

Disk.

2. Clean the Reel Disk Shaft and put in height

adjusting washers (3).

3. Be careful not to damage the Tension Band

Assy at the time of removal and installation.

4. Be careful not to scratch the Reel Disk Shaft

with the polyslider washer or the tool at the

time of removal and installation.

5. After oiling the Reel Disk Shaft, install the new

Reel Disk S Ass’y and Reel Disk T Ass’y

again.

6. After installation, adjust the height of the Reel

Disk. (Refer to item 1-1 of MECHANICAL

ADJUSTMENTS)

7. After installation, adiust and confirm the

tension post position. (Refer to item 1-2 of

MECHANICAL ADJUSTMENTS)

Fig. 2-3

2-4: A/C HEAD (Refer to Fig. 2-4)

1 Disconnect the 2 connectors (2 pins and 6

pins) on the A/C Head PCB.

2. Remove the screws (1), (2) and (3).

NOTES

1 Do not touch the heads by any means when

replacing the A/C Head.

2. After replacement, confirm the following

adjustments.

a. MECHANICAL ADJUSTMENTS: ITEM 2-2

b. MECHANICAL ADJUSTMENTS: ITEM 2-3

Fig. 2-4

Recommended Safety Parts

Item Part No. Description

2-5: LOADING MOTOR (Refer to Fig. 2-5)

1. Remove the lead wire in the hook of the

Loading Motor Box.

2. Remove the Loading Motor Belt.

3. Remove the 2 screws (1), then remove the

Loading Motor Box.

4. Remove the Front Loading Belt.

5. Remove the 2 screws (2), then lift the

Loading Motor upward.

6. Remove the 2 wires soldered to the Loading

Motor.

NOTES

1. Clean the pulley when replacing Front

Loading Belt and Loading Motor Belt.

2. Avoid getting grease on the Loading Motor

Belt and Front Loading Belt.

Fig. 2-5

2-6: PINCH ROLLER ARM (Refer to Fig. 2-6)

1. Remove the Pinch Roller Arm Spring.

2. Remove the polyslider washer (1).

3. Remove the Pinch Roller Arm.

NOTE

Do not touch the Pinch Roller. (Use gloves.)

Fig. 2-6

2-7: CYLINDER UNIT (Refer to Fig. 2-7)

1. Disconnect the connector (1).

2. Disconnect the connector (2).

3. Remove the 3 screws (3), then remove the

Head Amp PCB.

4. Remove the 3 screws (4), then remove the

Cylinder Unit from the Main Chassis.

NOTES

1. Do not touch the surface of the Cylinder

Head.

2. After replacement, confirm the following

adjustment.

MECHANICAL ADJUSTMENTS: ITEM 2-1

Fig. 2-7

2-8: DECK PCB (Refer to Fig. 2-8)

1. Remove the connector (9 pins) on the

Capstan DD Unit.

2. Remove the 2 solder traces (A) and remove

the 2 screws (1).

3. Remove the Deck PCB.

NOTES

1. When installing the Deck PCB, be sure to set

the Rotary Switch to the EJECT position.

The EJECT position is the point where the (B)

tooth is aligned to (C).

2. Avoid getting grease on the Reel Belt.

3. After installation, be sure to resolder traces

(A).

Fig. 2-8

2-9: CAPSTAN DD UNIT

(Refer to Fig. 2-9-A, B)

1. Remove the Loading Motor Belt.

2. Remove the screw (1), then remove the

Bracket Worm 3.

3. Remove the Worm.

4. Remove the 3 screws (1). (Refer to Fig. 2-9-

5. Remove the Capstan DD Unit.

NOTES

1. Do not bend the Limiter Post.

2. Use the specified screw held to the Capstan

DD Unit.

3. Install in the position where the Capstan DD

Unit PCB gets up to the (A) position.

1 2 3 4 5 6 ... 53 54

AIWA VX-T1420 1

Shrnutí obsahu

Strany 1 - AIWA VX-T1420

AIWA VX-T1420R1083 S6-150-12R-7J0 RES.FUSE 2.7-1WIC351 S0-1SP-526-500 IC, AN5265IC1002 S0-7S0-247-V10 IC, BA6247-V1IC1004 S0-QK9-780-500 IC, NJMT805F

Strany 2

AIWA VX-T1420TV Power Supply Diagram

Strany 3

AIWA VX-T1420VCR Head Amp DiagramVCR IF Diagram

Strany 4

AIWA VX-T1420VCR Operation PCB Diagram

Strany 5

AIWA VX-T1420VCR System Control & Servo Diagram

Strany 6

AIWA VX-T1420VCR Tuner Audio Diagram

Strany 7

AIWA VX-T1420VCR Y/C Diagram

Strany 8

AIWA VX-T1420Wiring Diagram

Strany 9

Strany 10

Strany 11

Strany 12

AIWA VX-T1420Disassembly InstructionsCont’dFig. 2-9-AFig. 2-9-B2-10: CAM 1 / CAM 2(Refer to Fig. 2-10-A, B, C)1. Remove the E-ring (1), then remove t

Strany 13

Strany 14

Strany 15

Strany 16

Strany 17

Strany 18

Strany 19

Strany 20

Strany 21

Strany 22

Strany 23

AIWA VX-T1420Mechanical AdjustmentsCont’d impossible to get satisfactory sound if thetape is distorted between the A/C head andP4 post.)3. If the

Strany 24

Strany 25

Strany 26

Strany 27

Strany 28

Strany 29

Strany 30

Strany 31

Strany 32

Strany 33

Strany 34

AIWA VX-T1420Mechanical PartsItem Part No. DescriptionMechanical Parts Cont’dItem Part No. Description301 S5-OP6-004-570 ARM, S-B BRKT 1302 S5-OA6-00

Strany 35

Strany 36

Strany 37

Strany 38

Strany 39

Strany 40

Strany 41

Strany 42

Strany 43

Strany 44

Strany 45

AIWA VX-T1420CRT Base Diagram

Strany 46

Strany 47

Strany 48

Strany 49

Strany 50

Strany 51

AIWA VX-T1420TV Deflection Diagram

Strany 52

AIWA VX-T1420TV Chroma Diagram

Strany 53

AIWA VX-T1420TV Microcontroller/Audio Amp Diagram

Strany 54

AIWA VX-T1420VCR AV Diagram

Komentáře k této Příručce

Žádné komentáře

Aiwa VX-T1470PH Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Kazetové přehrávače Aiwa VX-T1470PH. AIWA VX Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Kazetové přehrávače Aiwa VX-T1470PH